Go to the first, previous, next, last section, table of contents.


The rectangle commands operate on rectangular areas of the text: all the characters between a certain pair of columns, in a certain range of lines. Commands are provided to kill rectangles, yank killed rectangles, clear them out, fill them with blanks or text, or delete them. Rectangle commands are useful with text in multicolumn formats, and for changing text into or out of such formats.

When you must specify a rectangle for a command to work on, you do it by putting the mark at one corner and point at the opposite corner. The rectangle thus specified is called the region-rectangle because you control it in about the same way the region is controlled. But remember that a given combination of point and mark values can be interpreted either as a region or as a rectangle, depending on the command that uses them.

If point and the mark are in the same column, the rectangle they delimit is empty. If they are in the same line, the rectangle is one line high. This asymmetry between lines and columns comes about because point (and likewise the mark) is between two columns, but within a line.

C-x r k
Kill the text of the region-rectangle, saving its contents as the "last killed rectangle" (kill-rectangle).
C-x r d
Delete the text of the region-rectangle (delete-rectangle).
C-x r y
Yank the last killed rectangle with its upper left corner at point (yank-rectangle).
C-x r o
Insert blank space to fill the space of the region-rectangle (open-rectangle). This pushes the previous contents of the region-rectangle rightward.
M-x clear-rectangle
Clear the region-rectangle by replacing its contents with spaces.
M-x delete-whitespace-rectangle
Delete whitespace in each of the lines on the specified rectangle, starting from the left edge column of the rectangle.
C-x r t RET string RET
Insert string on each line of the region-rectangle (string-rectangle).

The rectangle operations fall into two classes: commands deleting and inserting rectangles, and commands for blank rectangles.

There are two ways to get rid of the text in a rectangle: you can discard the text (delete it) or save it as the "last killed" rectangle. The commands for these two ways are C-x r d (delete-rectangle) and C-x r k (kill-rectangle). In either case, the portion of each line that falls inside the rectangle's boundaries is deleted, causing following text (if any) on the line to move left into the gap.

Note that "killing" a rectangle is not killing in the usual sense; the rectangle is not stored in the kill ring, but in a special place that can only record the most recent rectangle killed. This is because yanking a rectangle is so different from yanking linear text that different yank commands have to be used and yank-popping is hard to make sense of.

To yank the last killed rectangle, type C-x r y (yank-rectangle). Yanking a rectangle is the opposite of killing one. Point specifies where to put the rectangle's upper left corner. The rectangle's first line is inserted there, the rectangle's second line is inserted at a position one line vertically down, and so on. The number of lines affected is determined by the height of the saved rectangle.

You can convert single-column lists into double-column lists using rectangle killing and yanking; kill the second half of the list as a rectangle and then yank it beside the first line of the list. See section Two-Column Editing, for another way to edit multi-column text.

You can also copy rectangles into and out of registers with C-x r r r and C-x r i r. See section Saving Rectangles in Registers.

There are two commands you can use for making blank rectangles: M-x clear-rectangle which blanks out existing text, and C-x r o (open-rectangle) which inserts a blank rectangle. Clearing a rectangle is equivalent to deleting it and then inserting a blank rectangle of the same size.

The command M-x delete-whitespace-rectangle deletes horizontal whitespace starting from a particular column. This applies to each of the lines in the rectangle, and the column is specified by the left edge of the rectangle. The right edge of the rectangle does not make any difference to this command.

The command C-x r t (M-x string-rectangle) replaces the rectangle with a specified string (inserted once on each line). The string's width need not be the same as the width of the rectangle. if the string's width is less, the text after the rectangle shifts left; if the stringis wider than the rectangle, the text after the rectangle shifts right.

Go to the first, previous, next, last section, table of contents.